Owner/Operator ManualModels926016 – ST11528DLE926017 – ST9526DLE926021 – ST9526DLET926022 – ST11528DLET926023 – ST1332DLET926500 – ST1332DLE926501 – S
GB - 10Check Track Tension (926021, 022, 023)Check tracking of unit with the differential locked, and tension of tracks (see Track Tension Adjustment
GB - 111. Attachment Clutch Lever2. Speed Selector3. Deflector Remote Control 4. Chute Control 5. Traction Drive Clutch Lever6. Oil Fill/Dipstick7. Mu
GB - 121. Attachment Clutch Lever2. Speed Selector3. Deflector Remote Control 4. Chute Control 5. Traction Drive Clutch Lever6. Oil Fill/Dipstick7. Di
GB - 13CONTROLS AND FEATURESSee Figure 10 for all Controls and Features locations.Dual Handle Interlock When Attachment Clutch and then Traction Drive
GB - 14Choke Control Knob1. Choke Closed position: chokes off air to engine for easier start.2. Choke Open position: allows for normal operation.IMPOR
GB - 15Discharge Chute ControlIMPORTANT: If chute does not stay in set position, adjust as directed in SERVICE AND ADJUSTMENTS on page 22, or repair
GB - 16Drift Cutters(Figure 15)Drift cutters break up snow drifts that are taller than the auger housing and direct the snow into the auger. Store the
GB - 17To add fuel to fuel tank: 1. ALWAYS place unit in open or well-ventilated area.2. Stop engine and allow to cool.3. Clean Fuel Cap and surroundi
GB - 18Manual Start1. Turn discharge chute straight ahead.2. Make sure that the traction clutch and attachment drive clutch levers are fully disengage
GB - 19IMPORTANT: DO NOT overload unit capacity by attempting to clear snow at too fast a rate. Use slow speed to clear deep or hard packed snow.Tips
GB - 29SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GB - 20CHECK DUAL HANDLE INTERLOCK Without the engine running, press down (engage) both clutch levers. Release attachment clutch lever. Attachment clu
GB - 21CLEAN BATTERY 926023, 500, 501IMPORTANT: Battery is maintenance-free. Do not tamper with or attempt to open battery. See SERVICE AND ADJUSTMENT
GB - 22SCRAPER BLADEIMPORTANT: Damage to auger/impeller housing will result if blade wears down too far.Scraper blade is adjustable to compensate for
GB - 23NOTE: Insert the hair pin with the loop end on the left side of the chute rod so the control lever will cover its full range of travel.6. Align
GB - 24If chute does not rotate freely:Tighten the cable by loosening the upper adjustment nut, and then tightening the lower adjustment nut against t
GB - 253. With the attachment clutch disengaged, check that the attachment idler arm lightly touches the frame. See Figure 31.4. Tighten jam nut on th
GB - 262. Adjust attachment idler position. See Figure 34.a. Loosen idler adjustment nut.b. To increase spring extension, move idler closer to belts a
GB - 272. Replace the belt cover.TRACTION DRIVE CLUTCH ADJUSTMENTIf drive slips, adjust traction clutch to compensate for friction disc wear.To adjust
GB - 283. Remove hair pin under the control panel connecting the discharge chute rod from the chute rotation lever and slide the discharge chute rod f
GB - 294. Install new traction drive belt onto attachment pulley and engine sheaves.5. Pull the drive plate assembly toward the friction disc and tigh
GB - 3DELIVERYCustomer Note: If you have purchased this product without complete assembly and instruction by your retailer, it is your responsibility
GB - 30SHORT TERMIMPORTANT: NEVER spray unit with high pressure water or store unit outdoors.Run with attachment clutch engaged a few minutes after ea
GB - 31 TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTION Engine will not crank/start.1. Fuel tank is empty.2. Fuel shut-off valve closed.3. Build up o
GB - 32SPECIFICATIONSModel Number 926016 926017 926021 926022DescriptionST11528DLE ST9526DLE ST9526DLET ST11528DLETEngine - TecumsehOH318SATecumsehOH
GB - 33SPECIFICATIONSModel Number 926023 926500 926501DescriptionST1332DLET ST1332DLE ST1336DLEEngine - TecumsehOH358SATecumsehOH358SATecu ms ehOH358
Ariens Company • 655 W. Ryan St. • Brillion, WI 54110-1072• (920) 756-2141 • www.ariens.com ALW2 - 61407Ariens Limited Warranties2-Year Limited Lawn a
Ariens Company • 655 W. Ryan St. • Brillion, WI 54110-1072• (920) 756-2141 • www.ariens.com ALW2 - 61407Exceptions, Limitations, ExclusionsThese warra
Ariens Company655 West Ryan StreetBrillion, WI 54110-1072920-756-2141Fax 920-756-2407www.ariens.com
GB - 41. WARNING!2. DANGER! 3. DANGER!SAFETY RULESRead, understand, and follow all safety practices in Owner/Operator Manual before beginning assembly
GB - 5Check for weak spots on docks, ramps or floors. Avoid uneven work areas and rough terrain. Stay alert for hidden hazards.DO NOT operate near dro
GB - 6ALWAYS shut off engine, remove key, and close fuel shut-off valve or drain fuel when transporting unit on a truck or trailer.Use extra care when
GB - 7PACKAGE CONTENTSASSEMBLYTools Required:•Pliers• Open-End Wrenches: 3/8, 7/16, 1/2, 9/16 in. and/or Adjustable Wrench• Tire GaugeUnfold Handlebar
GB - 84. Remove the cover from the gear assembly on the discharge chute.5. Release the lock teeth on the gear assembly with your finger and rotate the
GB - 910. Replace the gear cover removed in step 4.IMPORTANT: Rotate the discharge chute to the left when tightening the pedestal hardware to ensure c
Komentarze do niniejszej Instrukcji