Ariens 920402 - Sno-Tek 24E Instrukcja Operatora

04854400 • 4/15ENGLISHE10Service GuideModel920402 – Sno-Tek 24E (SN 175000 +)

EN – 9BOTTOM COVER REMOVALNOTICE: Save all hardware for reinstallation.1. Stop engine, remove key and wait for all moving parts to stop and for hot pa

EN – 10SEPARATE AUGER HOUSING FROM FRAMENOTICE: Save all hardware for reinstallation.1. Stop engine, remove key and wait for all moving parts to stop

EN – 11See Figure 8.7. Remove hardware securing belt finger to engine and remove belt finger.8. Remove attachment drive belt from attachment sheave.Se

EN – 12ATTACHMENT DRIVE BELT REPLACEMENTRemove Attachment Drive BeltNOTICE: Save all hardware for reinstallation.1. Stop engine, remove key and wait f

EN – 1313. Reinstall belt cover and tighten hardware.14. Reinstall chute rotation rod into chute rotation gear and secure with spring clip.15. Reinsta

EN – 14Install Traction Drive BeltSee Figure 15.1. Install belt onto traction drive pulley.2. Install belt onto traction sheave.3. Move swing gate so

EN – 15ATTACHMENT BRAKE REPLACEMENTRemove Attachment BrakeNOTICE: Save all hardware for reinstallation.1. Stop engine, remove key and wait for all mov

EN – 168. Remove bottom cover. See Bottom Cover Removal on page 9.See Figure 19.9. Check attachment brake:• Brake must contact attachment belt when at

EN – 17See Figure 21.6. Remove spring clip from right side of hex shaft.7. Remove hardware securing left flange bearing to frame and remove flange bea

EN – 187. Reinstall left flange bearing and secure with three tapping screws.8. Reinstall spring clip into hex shaft.9. Reinstall adjustment pivot pin

EN – 1SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3PRACTICES & LAWS . . . . . . . . . . . . . . . . . . 3REQUIRED OPERATOR

EN – 19See Figure 26.6. Remove hardware securing auger bushings to auger housing.See Figure 27.7. Remove auger assembly from auger housing.See Figure

EN – 204. Align holes in auger with holes in auger shaft and reinstall shear bolt. Torque bolt to 5.8 – 12.2 lbf-ft (7.9 – 16.5 N•m). If torque wrench

EN – 21AUGER GEARCASE REPLACEMENTRemove Gearcase AssemblyNOTICE: Save all hardware for reinstallation.1. Stop engine, remove key and wait for all movi

EN – 22ENGINE REPLACEMENTRemove EngineNOTICE: Save all hardware for reinstallation.1. Drain gasoline from tank and fuel system. See Draining Fuel Syst

EN – 23Install Engine1. Lower engine onto frame so weld screws in frame insert through mounting holes in engine base.2. Reinstall four locking washers

EN – 24See Figure 37.6. Disconnect lower traction drive cable from upper traction drive cable.7. Loosen, but DO NOT remove shoulder bolt retaining cab

EN – 25Install Bushing1. Install new bushing onto axle and align holes with holes in frame.2. Secure bushing to frame with two tapping screws from ins

EN – 26See Figure 41.5. Remove push nut from pinion gear and discard.6. Remove pinion gear and flat steel washer from pinion gear bracket.Install Pini

EN – 27Install Chute Rotation Gear1. Position discharge chute facing forward.See Figure 43.2. Position chute rotation gear on chute mount so gear teet

EN – 28SERVICE PARTSDescription Part No.Spark Plug 21547400Attachment Drive Belt 07200513Traction Drive Belt 07200603Friction Disc 00170800

EN – 2Have Questions or Need Assistance?www.ariens.com920-756-4688To find your nearest authorized Ariens service dealer, visit ariens.com and click “W

EN – 29SERVICE RECORDDATE SERVICE PERFORMED NOTES

655 West Ryan StreetBrillion, WI 54110920-756-4688Fax 920-756-2407www.ariens.comwww.ariens.com.au

EN – 3Read these safety rules and follow them closely. Failure to follow these rules could lead to loss of control of unit, severe personal injury or

EN – 4SAFETY DECALSThe safety decals on your machine are visual reminders of the important safety information in this manual. All messages on your uni

EN – 5SAFETY RULESThe following safety instructions are based on the B71.3 specifications of the American National Standards Institute in effect at th

EN – 6After striking a foreign object, stop the engine, remove the wire from the spark plug, disconnect the cord on electric motors, thoroughly inspec

EN – 7Always refer to operator's manual for important details if the snow thrower is to be stored for an extended period.Maintain or replace safe

EN – 8DRAINING FUEL SYSTEM1. Move unit to an open, well-ventilated area with no flames or sparks.2. Remove cap from fuel tank and siphon fuel into a c